--- title: "Output voltage of two op-amp IA" subject: "Advanced Electronics" chapter: 4 key: "semester_4/advanced_electronics:two-opamp-ia-output" source: https://www.bctengineer.com/q/semester_4/advanced_electronics/two-opamp-ia-output site: BCT Engineering --- # Output voltage of two op-amp IA Advanced Electronics · Chapter 4: Instrumentation and Isolation Amplifiers - Asked in: 2073 Chaitra, 4 marks - Video: [Instrumentation amplifier using two Op-Amps | IA using dual Op-Amps](https://www.youtube.com/watch?v=_PZ034AnZ68) — Electronics for You - Answer checked by Claude Opus 5.5 (high effort) on 2026-10-14 - Page: https://www.bctengineer.com/q/semester_4/advanced_electronics/two-opamp-ia-output - Whole chapter: https://www.bctengineer.com/md/semester_4/advanced_electronics/chapter-4 ## Question Calculate the output voltage for the 2 op-amp Instrumentation amplifier circuit shown in figure below. [Figure: Op-amp A1: V1 to its non-inverting input; its inverting input is connected to ground through R2 and to its own output through R1. Op-amp A2: V2 to its non-inverting input; the A1 output connects through R1 to the A2 inverting input; feedback resistor R2 from the A2 output V0 to its inverting input. A gain resistor R connects the inverting input of A1 to the inverting input of A2. Output V0 is taken from A2.] ## Short answer By virtual short and KCL at the inverting nodes, the output voltage is Vo = (1 + R2/R1 + 2R2/R)(V2 − V1). The differential gain is Ad = 1 + R2/R1 + 2R2/R. ## Answer This is the two op-amp instrumentation amplifier. Both inputs go to non-inverting terminals, so both inputs have very high input impedance. The gain resistor R between the two inverting inputs sets the gain. #### Circuit (as given) ```text GND--[R2]--+--[R1]--+ | | A (-)\ | A1>---+-Vo1-[R1]-+--[R2]--+ V1--(+)/ | | | B (-)\ | | A2>---+-> Vo | V2-------(+)/ | | +-------[ R ]-------+ (node A = inverting input of A1, node B = inverting input of A2) ``` #### Analysis By the virtual short, the inverting input of A1 (node A) is at **V1**, and the inverting input of A2 (node B) is at **V2**. The op-amp inputs draw no current. **KCL at node A** (currents leaving through R2 to ground, R1 to Vo1, and R to node B): ```text V1/R2 + (V1 − Vo1)/R1 + (V1 − V2)/R = 0 Vo1 = V1(1 + R1/R2) + (R1/R)(V1 − V2) ``` **KCL at node B** (currents leaving through R1 to Vo1, R2 to Vo, and R to node A): ```text (V2 − Vo1)/R1 + (V2 − Vo)/R2 + (V2 − V1)/R = 0 Vo = V2(1 + R2/R1) − (R2/R1)Vo1 + (R2/R)(V2 − V1) ``` **Substitute Vo1:** ```text (R2/R1)Vo1 = V1(1 + R2/R1) + (R2/R)(V1 − V2) Vo = V2(1 + R2/R1) − V1(1 + R2/R1) − (R2/R)(V1 − V2) + (R2/R)(V2 − V1) = (V2 − V1)(1 + R2/R1) + (2R2/R)(V2 − V1) ``` #### Result ```text Vo = (1 + R2/R1 + 2R2/R)(V2 − V1) Ad = 1 + R2/R1 + 2R2/R ``` **Example:** R1 = R2 = 10 kΩ, R = 2 kΩ gives Ad = 1 + 1 + 10 = 12. For V1 = V2 the output is zero, so common-mode signals are rejected (with matched resistors). The gain can be adjusted with R alone. Without R (R → ∞), Ad = 1 + R2/R1. ## Check yourself The answer's key points as multiple-choice questions, with the correct option and why. 1. In the two op-amp IA, what are the voltages at the inverting inputs of A1 and A2? A. Both zero B. V1 at A1 and V2 at A2, by virtual short C. Both V1 D. Vo1 and Vo Answer: B. Each op-amp's inverting input follows its non-inverting input. (Key point: Node voltages) 2. What is the differential gain of this circuit? A. 1 + R2/R1 + 2R2/R B. 1 + R1/R2 + 2R1/R C. R2/R1 D. 1 + 2R2/R Answer: A. Vo = (1 + R2/R1 + 2R2/R)(V2 - V1). (Key point: Final result) 3. For R1 = R2 = 10 kOhm and R = 2 kOhm, what is Ad? A. 7 B. 11 C. 12 D. 6 Answer: C. Ad = 1 + 1 + 2 x 10/2 = 12. (Key point: Numerical) ## Related in Advanced Electronics - [Find coefficients of op-amp summing circuit](https://www.bctengineer.com/question.md?key=semester_4%2Fadvanced_electronics%3Asumming-amplifier-coefficients) — Advanced Electronics, chapter 1 - [Output offset voltage of 741 inverting amplifier](https://www.bctengineer.com/question.md?key=semester_4%2Fadvanced_electronics%3Aoutput-offset-741-inverting) — Advanced Electronics, chapter 2 - [IA features; 3 op-amp IA output voltage](https://www.bctengineer.com/question.md?key=semester_4%2Fadvanced_electronics%3Aia-features-3opamp-output) — Advanced Electronics, chapter 4 - [Output of log-ratio amplifier with RT compensation](https://www.bctengineer.com/question.md?key=semester_4%2Fadvanced_electronics%3Alog-ratio-temperature-compensated) — Advanced Electronics, chapter 5 - [Output of temperature-compensated log circuit](https://www.bctengineer.com/question.md?key=semester_4%2Fadvanced_electronics%3Atemperature-compensated-log-circuit) — Advanced Electronics, chapter 5 - [3 op-amp IA output and common-mode rejection](https://www.bctengineer.com/question.md?key=semester_4%2Fadvanced_electronics%3Athree-opamp-ia-cm-rejection) — Advanced Electronics, chapter 4 ## Related in other subjects - [Voltage gain of non-inverting op-amp](https://www.bctengineer.com/question.md?key=semester_2%2Fbasic_electronics_engineering%3Aopamp-noninverting-gain) — Basic Electronics Engineering, chapter 4, asked 2× - [Non-inverting op-amp voltage gain](https://www.bctengineer.com/question.md?key=semester_1%2Ffundamental_of_electrical_and_electronics_engineering%3Anon-inverting-amplifier-gain) — Fundamental of Electrical and Electronics Engineering, chapter 6 - [Ideal op-amp properties; non-inverting gain](https://www.bctengineer.com/question.md?key=semester_2%2Fbasic_electronics_engineering%3Aopamp-props-noninverting-gain) — Basic Electronics Engineering, chapter 4, asked 3× - [Transfer function of op-amp phase-shift circuit](https://www.bctengineer.com/question.md?key=semester_3%2Fcontrol_systems%3Atf-opamp-allpass-r1-c-r2) — Control Systems, chapter 2, asked 2×