---
title: "Popularity of compressive test; tensile methods"
subject: "Concrete Technology and Masonry Structure"
chapter: 5
key: "semester_5/concrete_technology_and_masonry_structure:compressive-popularity-tensile-methods"
source: https://www.bctengineer.com/q/semester_5/concrete_technology_and_masonry_structure/compressive-popularity-tensile-methods
site: BCT Engineering
---

# Popularity of compressive test; tensile methods

Concrete Technology and Masonry Structure · Chapter 5: Testing of concrete and quality control

- Asked in: 2068 Chaitra, 8 marks
- Video: [Compressive Strength of Cement Concrete Cubes](https://www.youtube.com/watch?v=e8bH26-3PCw) — NCTEL
- Answer checked by Claude Sonnet 5.5 on 2026-10-14
- Page: https://www.bctengineer.com/q/semester_5/concrete_technology_and_masonry_structure/compressive-popularity-tensile-methods
- Whole chapter: https://www.bctengineer.com/md/semester_5/concrete_technology_and_masonry_structure/chapter-5

## Question

Explain the reasons for popularity of the compressive strength test of concrete. Describe different methods of obtaining tensile strength of concrete.

## Short answer

The compressive test is popular because it is simple, fast, concrete is mainly used in compression, and it serves as a quality index. Tensile strength methods: direct tension (rare), splitting (f_sp = 2P/(pi L d) on a cylinder), and flexure (f_cr = P l/(b d^2) on a beam).

## Answer

#### Reasons for the popularity of the compressive strength test
1. The test is **simple and quick** and needs only a cube mould and a compression machine, which every site laboratory has.
2. Concrete is mainly used in compression, so compressive strength is the main design property.
3. Other properties (tensile, flexural, shear, bond, modulus) can be estimated from $f_{ck}$ (IS 456 Cl. 6.2).
4. It is a good index of overall quality: durability, density and impermeability improve as strength rises.
5. Results are reproducible and the standard (IS 516, IS 456 Cl. 15 and 16) is universal, so the test is used for mix design, quality control and acceptance.
6. Compressive strength is much higher than tensile strength, so it can be measured with a smaller relative error.

#### Methods of obtaining tensile strength
**1. Direct tension test.** A dog-bone or cylindrical specimen with embedded end grips is pulled axially. It is rarely used, because it is hard to avoid eccentricity and secondary stresses from the grips, and the result scatters. Direct tensile strength is about $0.35\sqrt{f_{ck}}$ to $0.45\sqrt{f_{ck}}$ (MPa).

**2. Splitting tension test (Brazilian test, IS 5816).** A standard cylinder (150 mm dia × 300 mm long) is laid horizontally between the platens of the testing machine, with thin plywood or fibre strips (about 3 mm thick and 15 mm wide) along the contact lines. The compressive line load is increased at a rate of 1.2 to 2.4 N/mm$^2$/min (splitting tensile stress) until the cylinder splits along the vertical diameter. The load applied gives a nearly uniform tensile stress across the loaded plane:

$$
f_{sp} = \frac{2P}{\pi L d}
$$

where $P$ = failure load, $L$ = length and $d$ = diameter of cylinder. Splitting strength is higher than direct tension by 5 to 12%, and about 0.5 to 0.6$\sqrt{f_{ck}}$ in MPa.

**Advantages:** it is simple, uses the same cylinders and compression machine as the compression test, and gives a more uniform and reproducible result than direct tension, with no grip problem.

**3. Flexure test (modulus of rupture, IS 516).** A plain concrete beam 150 × 150 × 700 mm is supported on a 600 mm span and loaded at the third points (two-point loading) at 0.7 N/mm$^2$/min extreme-fibre stress rate. If the crack occurs in the middle third:

$$
f_{cr} = \frac{P\,l}{b\,d^{2}}
$$

If the crack is outside the middle third but within 5% of the span from the load point, $f_{cr} = 3Pa/(bd^2)$ ($a$ = distance of the crack from the nearer support); otherwise the result is rejected. For single (centre) point loading, $f_{cr} = 3Pl/(2bd^2)$. IS 456 (Cl. 6.2.2) gives the flexural strength $f_{cr} = 0.7\sqrt{f_{ck}}$ N/mm$^2$. The modulus of rupture is greater than direct tension (by about 1.5 to 2 times) because the stress distribution is assumed linear while the actual stress block is plastic.

## Check yourself

The answer's key points as multiple-choice questions, with the correct option and why.

1. Which is a reason for the popularity of the compressive test?
   A. Simple, quick, and other properties can be estimated from fck
   B. It needs special grips
   C. It directly measures tension
   D. It is not standardised
   Answer: A. It is simple and fck is the basis for deriving other properties. (Key point: Popularity)

2. Why is compressive strength a good overall quality index?
   A. It is independent of density
   B. Durability, density and permeability improve as strength rises
   C. It measures only the steel
   D. It decreases with durability
   Answer: B. Higher strength generally implies denser, less permeable, more durable concrete. (Key point: Index of quality)

3. How does splitting strength compare with direct tension?
   A. 50% lower
   B. Equal
   C. 5 to 12% higher
   D. Two times higher
   Answer: C. Splitting strength exceeds direct tension by about 5 to 12%. (Key point: Split strength vs direct)

4. Why is the modulus of rupture greater than direct tension?
   A. Beams contain steel
   B. The load is applied faster
   C. Beams are cured longer
   D. The linear stress distribution is assumed while the actual stress block is plastic
   Answer: D. Assuming linear stress overestimates the true extreme-fibre stress. (Key point: Modulus of rupture)

## Related in Concrete Technology and Masonry Structure

- [Compressive strength test of brick wall](https://www.bctengineer.com/question.md?key=semester_5%2Fconcrete_technology_and_masonry_structure%3Acompressive-test-masonry-wall) — Concrete Technology and Masonry Structure, chapter 10, asked 4×
- [Compressive strength test of masonry prism](https://www.bctengineer.com/question.md?key=semester_5%2Fconcrete_technology_and_masonry_structure%3Acompressive-test-masonry-prism) — Concrete Technology and Masonry Structure, chapter 10, asked 2×
- [Compressive strength test; acceptance criteria](https://www.bctengineer.com/question.md?key=semester_5%2Fconcrete_technology_and_masonry_structure%3Acompressive-test-procedure-acceptance) — Concrete Technology and Masonry Structure, chapter 5
- [Tensile strength tests of concrete](https://www.bctengineer.com/question.md?key=semester_5%2Fconcrete_technology_and_masonry_structure%3Atensile-strength-tests) — Concrete Technology and Masonry Structure, chapter 5, asked 2×
- [Tests for compressive and tensile strength](https://www.bctengineer.com/question.md?key=semester_5%2Fconcrete_technology_and_masonry_structure%3Astrength-tests-compression-tension) — Concrete Technology and Masonry Structure, chapter 5, asked 4×
- [Importance and method of compressive strength test](https://www.bctengineer.com/question.md?key=semester_5%2Fconcrete_technology_and_masonry_structure%3Acompressive-strength-importance-method) — Concrete Technology and Masonry Structure, chapter 5

## Related in other subjects

- [Compressive strength test and classification of bricks](https://www.bctengineer.com/question.md?key=semester_5%2Fdesign_of_timber_and_masonry_structures%3Abrick-compressive-strength-test-classification) — Design of Timber and Masonry Structures, chapter 8
- [Compressive strength test of cement](https://www.bctengineer.com/question.md?key=semester_3%2Fcivil_engineering_materials%3Acement-compressive-strength-test) — Civil Engineering Materials, chapter 5, asked 3×
- [T-beam: maximum tensile and compressive stress](https://www.bctengineer.com/question.md?key=semester_3%2Fstrength_of_materials%3At-beam-udl-40kn-30cm-tension) — Strength of Materials, chapter 7
- [Regression of permeability on compressive strength](https://www.bctengineer.com/question.md?key=semester_5%2Fprobability_and_statistics%3Aconcrete-permeability-regression-sums) — Probability and Statistics, chapter 5