--- title: "Bridge components; tunnel drainage and ventilation" subject: "Transportation Engineering II" chapter: 5 key: "semester_7/transportation_engineering_ii:bridge-components-tunnel-drainage-ventilation-problems" source: https://www.bctengineer.com/q/semester_7/transportation_engineering_ii/bridge-components-tunnel-drainage-ventilation-problems site: BCT Engineering --- # Bridge components; tunnel drainage and ventilation Transportation Engineering II · Chapter 5: Introduction to Bridge and Tunnel Engineering - Asked in: 2073 Shrawan, 8 marks - Video: [Transportation Engineering-II U-4 L-6 Tunnel Drainage](https://www.youtube.com/watch?v=9OHbWssslrY) — Namrata Singh - Answer checked by Claude Opus 5.5 (high effort) on 2026-10-14 - Page: https://www.bctengineer.com/q/semester_7/transportation_engineering_ii/bridge-components-tunnel-drainage-ventilation-problems - Whole chapter: https://www.bctengineer.com/md/semester_7/transportation_engineering_ii/chapter-5 ## Question Show the various component parts of bridge with a neat sketch. How drainage and ventilation problems are managed while tunneling? ## Short answer Drainage is managed by gravity side ditches for up-gradient headings, sumps and pumping for down-gradient headings, pre-grouting, and permanent side or central drains with a waterproof membrane. Ventilation uses fresh-air supply systems to dilute CO, NOx and smoke, maintain visibility, and control smoke in fires. ## Answer #### Components of a bridge A bridge has a **superstructure** (above the bearings) and a **substructure** (bearings, piers, abutments and foundations), plus approaches and protective works. ```text Approach Parapet/Railing Deck slab Approach slab ________________________ slab ____ ____|_____|_____|_____|_____|____ ____ \ | [girder][girder][girder] | / Wing \ |Bearing Bearing | / Wing wall |Abutment [ PIER ] Abutment| wall | | | | | HFL ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Scour level - - - - - - - - - - - - - - - - [Footing] [Pile/Well] [Footing] ``` **Superstructure** - **Deck slab and wearing coat:** carry the traffic loads (IRC Class A/70R/AA loading as per IRC:6) to the girders. - **Girders/trusses/arches:** the main load-carrying members that span between supports. - **Cross girders/diaphragms:** give lateral stability and distribute the load. - **Parapets, railings, kerbs and footpaths:** provide safety for vehicles and pedestrians. - **Expansion joints and drainage spouts:** allow thermal movement and remove surface water. **Bearings:** transmit reactions from the superstructure to the substructure and permit rotation and movement (elastomeric, roller and rocker types). **Substructure** - **Abutments:** end supports that also retain the approach fill, with **wing walls** and **return walls** that hold back the earth. - **Piers:** intermediate supports carrying the vertical load, with a pier cap and bed block. - **Foundations:** open (spread) footings, piles, wells or caissons that carry the loads to sound strata below the scour depth. **Others:** approach embankment and approach slab, **protective works** (guide bunds, spurs, apron, pitching) and river training works. The design HFL, LWL and scour level are marked on the section. #### Management of drainage problems Water entering a tunnel from rock joints, springs or the portals makes excavation unsafe, softens the ground, damages the lining and reduces working efficiency, so drainage is planned at every stage. **During construction** - **Gravity drainage:** if the tunnel is driven up-gradient (rising heading), water flows out by itself through a **side ditch/gutter** or pipe at the invert. The gradient is commonly 0.2–0.5%. - **Sumps and pumping:** if the tunnel is driven down-gradient (falling heading), water collects at the face in a **sump** and is pumped out in stages through pipes with booster pumps. - **Pre-grouting and probe holes:** cement or chemical grout is injected ahead of the face to seal water-bearing zones; probe drilling detects water in advance. - **Dewatering of the ground:** well points, deep wells and drainage holes (or a drainage drift) in poor ground. - **Sealing:** shotcrete, waterproof membrane and concrete lining, with good control of leakage. **Permanent drainage (road tunnel)** - **Side/central drains** with covered manholes and cleaning chambers, and sufficient cross-fall (usually 1–2%) on the carriageway. - **Drainage behind the lining:** perforated pipes and geotextile fleeces behind the lining carry seepage to the invert drain, so that hydrostatic pressure does not act on the lining. - **Waterproof membrane (PVC/HDPE)** between the primary and final linings. - **Portal drainage:** cut-off drains above the portal to divert surface water, and a catch drain. - **Fire/oil separators** for drained liquids in road tunnels, in line with IRC:SP:91. #### Management of ventilation problems Vehicles in a tunnel emit CO, NOx, hydrocarbons and smoke, and blasting and diesel plant add dust and fumes during construction. Ventilation supplies fresh air and dilutes or removes pollutants, keeping visibility and air quality within safe limits (IRC:SP:91 and PIARC give limits, e.g. CO of about 70–100 ppm for normal traffic, and visibility limits for smoke). **Natural ventilation** - Relies on the **piston effect** of moving vehicles and on wind and temperature differences between the portals. - Suitable only for short tunnels (below about 300–500 m) with low traffic; it is not dependable. **Mechanical (artificial) ventilation** 1. **Longitudinal system:** jet fans hung from the roof push air along the tunnel from one portal to the other. It is simple and economical, and suits one-way tunnels of moderate length. 2. **Semi-transverse system:** fresh air is supplied through a duct along the tunnel and escapes through the portals (or the reverse: an exhaust duct, with fresh air entering at the portals). Used for medium to long tunnels. 3. **Fully transverse system:** separate supply and exhaust ducts; fresh air is supplied uniformly along the length and polluted air is extracted. It gives the best control but is costly; used for long tunnels with heavy traffic, and it also helps with smoke control during a fire. 4. **Shaft ventilation:** vertical or inclined shafts with fans in long tunnels, to remove exhaust at intermediate points. 5. **Ventilation during construction:** forced (blowing) or exhaust ventilation with flexible ducts and fans, often a combined (push-pull) system. ```text Longitudinal: ->J- J- J- J-> (jet fans, air flows end to end) Semi-transverse: [supply duct] ==> air leaves at portals Transverse: [supply duct] --- tunnel --- [exhaust duct] ``` The choice of system depends on the length, traffic volume, gradient, number of lanes and cost; CO and visibility sensors control fan operation. ## Check yourself The answer's key points as multiple-choice questions, with the correct option and why. 1. Which set belongs to the substructure of a bridge? A. Deck slab, girders, parapets B. Piers, abutments, foundations C. Railings, kerbs, expansion joints D. Wearing coat and drainage spouts Answer: B. The substructure comprises bearings, piers, abutments and foundations that transfer loads to the ground. (Key point: Superstructure vs substructure) 2. What do bearings do? A. Retain the approach fill B. Transmit reactions from superstructure to substructure and permit rotation and movement C. Divert the river flow D. Carry traffic loads directly Answer: B. Bearings sit between girders and piers/abutments, passing reactions down while allowing rotation and thermal movement. (Key point: Role of bearings) 3. When can water drain by gravity out of a tunnel under construction? A. When driven down-gradient B. When driven up-gradient (rising heading), through a side ditch C. Never D. Only with pumps Answer: B. A rising heading lets water flow out along an invert ditch or pipe. (Key point: Gravity drainage) 4. If a tunnel is driven down-gradient, water is handled by: A. Letting it flood B. Collecting in a sump at the face and pumping out in stages C. Gravity ditch D. Grouting the portal only Answer: B. Falling headings need sumps and booster pumping. (Key point: Sumps) ## Related in Transportation Engineering II - [Bridge components; tunnel drainage and ventilation](https://www.bctengineer.com/question.md?key=semester_7%2Ftransportation_engineering_ii%3Abridge-components-tunnel-drainage-ventilation) — Transportation Engineering II, chapter 5 - [Ideal bridge characteristics; tunnel drainage](https://www.bctengineer.com/question.md?key=semester_7%2Ftransportation_engineering_ii%3Aideal-bridge-characteristics-tunnel-drainage) — Transportation Engineering II, chapter 5 - [Tunnel ventilation methods; bridge site selection factors](https://www.bctengineer.com/question.md?key=semester_7%2Ftransportation_engineering_ii%3Atunnel-ventilation-methods-bridge-site-selection) — Transportation Engineering II, chapter 5, asked 2× - [Tunnel ventilation methods; bridge site factors](https://www.bctengineer.com/question.md?key=semester_7%2Ftransportation_engineering_ii%3Atunnel-ventilation-methods-bridge-site-factors) — Transportation Engineering II, chapter 5, asked 2× - [Bridge site factors; importance of tunnel ventilation](https://www.bctengineer.com/question.md?key=semester_7%2Ftransportation_engineering_ii%3Abridge-site-factors-tunnel-ventilation-importance) — Transportation Engineering II, chapter 5 - [Ideal bridge site; tunnel ventilation need and methods](https://www.bctengineer.com/question.md?key=semester_7%2Ftransportation_engineering_ii%3Aideal-bridge-site-tunnel-ventilation) — Transportation Engineering II, chapter 5 ## Related in other subjects - [Fault, parts, recognition, engineering problems](https://www.bctengineer.com/question.md?key=semester_3%2Fengineering_geology_i%3Afault-parts-recognition-engineering-problems) — Engineering Geology I, chapter 5