Skip to main content

Uses of microwaves in communication and protocols

Short answer

Microwaves are used in terrestrial backhaul, satellite, cellular, Wi-Fi, Bluetooth, radar, GPS, and telemetry. Three protocols: Wi-Fi (2.4/5 GHz, OFDM, CSMA/CA), cellular (GSM 900/1800 MHz with GMSK/TDMA, LTE OFDMA, 5G NR), and satellite (C/Ku/Ka bands, FDMA/TDMA/CDMA, QPSK/DVB-S2).

List out the uses of microwaves in communication systems and [?] communication protocols of any three of them.

Uses of microwaves in communication systems

  1. Terrestrial point-to-point microwave links (backhaul for mobile networks and TV relay).
  2. Satellite communication (telephony, DTH TV, VSAT, Internet).
  3. Cellular mobile communication (GSM, CDMA, LTE, 5G).
  4. Wireless LAN (Wi-Fi) and WiMAX.
  5. Personal area networks (Bluetooth, ZigBee).
  6. Navigation (GPS, radar beacons, aircraft landing systems).
  7. Radar (it conveys target information through reflected signals).
  8. Deep-space and telemetry links.

Communication protocols of three of them

1. Wi-Fi (IEEE 802.11 WLAN)

  • Bands: 2.4 GHz ISM (2.400–2.4835 GHz), 5 GHz (5.15–5.85 GHz), and 6 GHz for Wi-Fi 6E.
  • Channels: 20/40/80/160 MHz wide. At 2.4 GHz there are 13 channels 5 MHz apart, and only 1, 6 and 11 do not overlap.
  • Modulation: OFDM with BPSK up to 1024-QAM (802.11ax). 802.11b used DSSS/CCK.
  • Access: CSMA/CA with optional RTS/CTS. Duplexing is TDD.
  • Rates: 11 Mbps (b), 54 Mbps (a/g), 600 Mbps (n, MIMO), about 9.6 Gbps (ax).
  • Security: WPA2/WPA3 (AES).

2. Cellular mobile (GSM / LTE / 5G NR)

  • GSM: 900/1800 MHz, 200 kHz carriers, GMSK modulation, TDMA with 8 time slots per carrier, FDD (uplink 890–915 MHz, downlink 935–960 MHz).
  • LTE (4G): 700 MHz–2.6 GHz, 1.4–20 MHz bandwidth, OFDMA downlink and SC-FDMA uplink, up to 64-QAM, MIMO, FDD or TDD.
  • 5G NR: FR1 below 6 GHz and FR2 at 24–52 GHz (mm-wave), up to 400 MHz bandwidth, flexible numerology, massive MIMO and beamforming.
  • Architecture: mobile station, base station (BTS/eNodeB/gNB), core network. Frequency reuse in hexagonal cells, with handover between cells.

3. Satellite communication

  • Geostationary orbit at 35,786 km. The ground-to-satellite delay is about 120 ms, so one hop (up and down) takes about 240 ms.
  • Bands: C band (uplink 5.925–6.425 GHz, downlink 3.7–4.2 GHz, written 6/4 GHz), Ku band (14/12 GHz), Ka band (30/20 GHz).
  • A transponder receives the uplink, translates the frequency down, amplifies with a TWTA or SSPA, and retransmits. Typical transponder bandwidth is 36 MHz.
  • Access: FDMA, TDMA, CDMA. Example: VSAT networks with QPSK/8PSK and DVB-S2.
  • Uplink is at the higher frequency because the ground station can afford more power to overcome the greater loss.

✓ Answer checked by Claude Opus 5.5 (high effort)

Related questions

All RF and Microwave Engineering chapter 1 questions →