Skip to main content

Sensitivity of -3; Q of Tow-Thomas LPF

Short answer

S^y_x = -3 means a 1% increase in x gives about a 3% decrease in y. For the Tow-Thomas low-pass filter, Q sensitivity: S^Q_R2 = 1, S^Q_C1 = 1/2, S^Q_R1 = S^Q_R4 = S^Q_C2 = -1/2, and S^Q_R3 = S^Q_r = 0.

What do you understand when the sensitivity of y with respect to x is equal to -3? Perform sensitivity analysis for Quality factor Q of the Tow Thomas low pass filter with respect to all the resistors and capacitors present in the circuit.

Meaning of Sxy=−3S^y_x = -3

Δyy≈−3Δxx\frac{\Delta y}{y} \approx -3\frac{\Delta x}{x}

A 1% increase in xx gives about a 3% decrease in yy: the change is three times larger and in the opposite direction. yy is quite sensitive to xx.

Sensitivity of Q of the Tow-Thomas low-pass filter

Tow-Thomas low-pass biquad: OA1 is a lossy integrator (R2∥C1R_2 \parallel C_1 in feedback, inputs VinV_{in} through R3R_3 and V3V_3 through R1R_1), OA2 is an integrator (R4R_4, C2C_2), and OA3 is a unity-gain inverter (V3=−V2V_3 = -V_2) built with two equal resistors rr (the gain stays −1-1 when both change together).

        +------R2------+
        +------||------+
        |      C1      |        +--||--+
Vin-R3--+--|-\         |        |  C2  |
        |  |  >--------+--R4----+-|-\  |
        |  +|/  V1     (OA1)    | |  >-+-- V2 (LP)
        | GND                GND+|/    |
        |                     (OA2)    |
        +--R1-- V3 --[inverter -1]-----+
                         (OA3)

Node equations (ideal op-amps):

V1(1R2+sC1)=−VinR3−V3R1V2=−V1sR4C2,V3=−V2\begin{aligned} V_1\left(\frac{1}{R_2} + sC_1\right) &= -\frac{V_{in}}{R_3} - \frac{V_3}{R_1} \\ V_2 &= -\frac{V_1}{sR_4C_2}, \qquad V_3 = -V_2 \end{aligned}

Solving:

T(s)=V2Vin=1R3R4C1C2s2+sR2C1+1R1R4C1C2T(s) = \frac{V_2}{V_{in}} = \frac{\dfrac{1}{R_3R_4C_1C_2}}{s^2 + \dfrac{s}{R_2C_1} + \dfrac{1}{R_1R_4C_1C_2}}

So

ωo=1R1R4C1C2=R1−1/2R4−1/2C1−1/2C2−1/2,Q=ωoR2C1=R2C1R1R4C2\omega_o = \frac{1}{\sqrt{R_1R_4C_1C_2}} = R_1^{-1/2}R_4^{-1/2}C_1^{-1/2}C_2^{-1/2}, \qquad Q = \omega_o R_2C_1 = R_2\sqrt{\frac{C_1}{R_1R_4C_2}}

Sensitivity of QQ: Q=R2 C11/2 R1−1/2R4−1/2C2−1/2Q = R_2\,C_1^{1/2}\,R_1^{-1/2}R_4^{-1/2}C_2^{-1/2}, so

SR2Q=1,SC1Q=12,SR1Q=SR4Q=SC2Q=−12,SR3Q=SrQ=0S^{Q}_{R_2} = 1, \quad S^{Q}_{C_1} = \frac12, \quad S^{Q}_{R_1} = S^{Q}_{R_4} = S^{Q}_{C_2} = -\frac12, \quad S^Q_{R_3} = S^Q_r = 0

For example, SR2Q=R2Q⋅∂Q∂R2=R2Q⋅QR2=1S^Q_{R_2} = \dfrac{R_2}{Q}\cdot\dfrac{\partial Q}{\partial R_2} = \dfrac{R_2}{Q}\cdot\dfrac{Q}{R_2} = 1.

Check: sum over resistors =1−12−12=0= 1 - \frac12 - \frac12 = 0, sum over capacitors =12−12=0= \frac12 - \frac12 = 0, as expected for a dimensionless quantity.

ElementSQS^Q
R1R_1, R4R_4, C2C_2−1/2 each
R2R_21
C1C_11/2
R3R_3, inverter rr0

✓ Answer checked by Claude Sonnet 5.5

All Filter Design chapter 7 questions →